
Realistic Response Times with Wireless Call Buttons
Realistic Response Times with Wireless Call Buttons
The average time that it takes for a call button to reach a member of staff is not a fixed figure, and varies depending upon a number of factors including the size of your premises and the number of staff on duty. Knowing the limits of your call button system helps you to understand whether you need to make changes to your staffing in order to ensure that your customers receive the service that they deserve.
Two Different Clocks Running
Press-to-acknowledgement time and press-to-arrival time are two separate measurements that often are confused with each other. The first one describes the time it takes for a call to be pressed by a guest or patient until it is acknowledged by staff. This can be within a couple of seconds by triggering a light, a buzz or a pager alert. The second one describes the time it takes for staff to arrive at the guest or patient after the call has been pressed. This time can vary greatly and is influenced by how busy staff are, how far apart guests or patients are and how long it takes to get to them.
Benchmarks Vary by Setting
A café with four tables and one staff member would typically expect to get to a table within a minute or two of a call being pressed. Restaurants however have very different peak times. A Saturday dinner service could expect a response within 3-5 minutes even with the best run of staff. A salon would typically be quicker as staff are usually stationed near a chair. In Care settings however, help could be needed for a fall or for a routine request such as for water and an arrival time would be set for each resident depending on their risk level.
Staffing Ratios Set the Ceiling
Good hardware can’t compensate for a bad ratio. If one person is covering fifteen tables, six bedrooms or the whole of a salon then even if wireless call buttons are used to send the alerts as quickly as possible, there’s a limit to how quickly the person can travel between calls. Work out your own ratio for the zones that one person would cover during your busiest hour and then work out how long it would take to walk between them all, even if there were no interruptions. If this is greater than two minutes then the best response time that you could achieve is going to be capped by this.
Why the Acknowledgement Light Matters
The acknowledgement light (or vibration etc.) has a major effect on customer perception of time. In industry terms this is known as the acknowledgement time. Without a visible / felt acknowledgement of a call being received the press of a button can result in nothing appearing to happen. The customer may press the button again and again, even eventually get up and ask at the till / bar etc. to see if anyone has noticed. This results in duplicate alerts being sent to staff, who appear to be slow to respond. This step is key in telecare systems and is generally recognised in industry terms as a separate time to the response time.
How Many Calls One Person Can Clear
One person can handle around 10-15 calls per hour depending on the length of time it takes to deal with each. Typically this is less than 30 seconds for something like a drink top up but can be up to 5 minutes to assist someone to a chair or deal with a complaint. But these numbers are based on ideal situations, if your numbers are consistently higher than this then you have a situation where the number of staff on duty is not sufficient to cope with the volume of business and research has shown that customers perceive waiting time to increase dramatically when they are able to see a queue of unanswered calls building.
Measure Your Own Numbers for a Week
Instead of using arbitrary numbers to measure the time it takes for people to get to tables, it’s much more accurate to actually measure the time it takes. For one week, keep a log at the till, bar, etc. of the following: time pressed, time acknowledged, and time of arrival. This will give you some accurate averages for the quietest time of day and the busiest time of day. This is actually measuring the time it takes for people to get to tables, as opposed to the arbitrary numbers manufacturers state on their spec sheets. This will give you some accurate numbers to work with based on your unique floor, staff and busy times.
When It’s Staffing, Not Equipment
A small difference in understanding how a call button system functions can lead to large misunderstandings when a button or receiver fails to function as expected. Fitting Wireless Call Buttons on your customers’ tables shortens the distance from customers needing help and your staff knowing that help is needed. But wireless call buttons can’t make staffing problems go away. In the industry of telecare many services provided by councils for residents are ringed up quickly but there are not enough responders to answer them. So don’t assume a button or receiver has failed when a late arrival is logged against a call button that has been previously confirmed to be functioning correctly. Possibly one person is trying to cover too much ground.
Measuring and managing response time is so much more important than purchasing equipment that offers to manage response time for you. By doing this you will get a far better understanding of your floor.
